Various
Ductile “Y” type filter with Flanges PN25 Fig.42N
– Mounting length according to EN 558-1 Serie 1. DIN 3202-1 / F1.
– Flange dimensions according to UNE-EN 1092-2 PN25.
– Hole dimensions according to UNE-EN 1092-2 PN25.
OPTIONS:
– Body-lid joint in rubber, cardboard or graphite.
– Different mesh microns in sieve.
– Plugs before and after the sieve to check pressure drop.
Double Sphere Rubber Expansion Joint Threaded Ends Fig. 83
Threaded ends according to: DIN 259 / 2999.
CHARACTERISTICS:
– They allow the adsorption of the four movements: compression, elongation, lateral deflection and angular deflection.
– They eliminate the noises and compensate the vibrations produced by the pumps or other equipment with pressure, temperature or corrosive fluids conditions.
– It occupies a little length of installation and is very light.
– It has a reduced fatigue factor and a great resistance to the deformation, being as well resistant corrosion and erosion.
– It doesn’t have an electrical continuity.
– It’s easy to assemble because it has floating flanges.
-The work temperature is between: -15 ºC and 90ºC. – Working pressure: 10 bar.
– Explosion pressure: 30 bar.
– Main utilities: Cold water, hot water, air, oils, fats, gas, gas oil, hydrogen…
MOUNTING:
– It is important that we always place the sleeve as close as possible to the pump and that the other end of it is well anchored using an anchor or fixed point, thus resulting in perfect isolation from vibration and noise.
– To absorb movements in pipes, the sleeve must be inserted respecting the placement of the fixed points and guides.
Single Sphere Rubber Expansion Joint With Flanges Fig. 82
Flanges dimensions and holes according to: DIN 2576 PN10 y DIN 2502 PN16.
CHARACTERISTICS:
– They allow the adsorption of the four movements: compression, elongation, lateral deflection and angular deflection.
– They eliminate the noises and compensate the vibrations produced by the pumps or other equipment with pressure, temperature or corrosive fluids conditions.
– It occupies a little length of installation and is very light.
– It has a reduced fatigue factor and a great resistance to the deformation, being as well resistant corrosion and erosion.
– It doesn’t have an electrical continuity.
– It’s easy to assemble because it has floating flanges.
– The work temperature is between: -15 ºC and 90ºC.
– Working pressure: 10 bar / 16 bar.
– Explosion pressure: 30 bar. – Main utilities: Cold water, hot water, air, oils, fats, gas, gas oil, hydrogen…
MOUNTING:
– It is important that we always place the sleeve as close as possible to the pump and that the other end of it is well anchored using an anchor or fixed point, thus resulting in perfect isolation from vibration and noise.
– To absorb movements in pipes, the sleeve must be inserted respecting the placement of the fixed points and guides.
Dismantling Joint Fig. 80
– Flange dimensions and holes according to: DIN 2576 PN10, DIN 2502 PN16 and DIN 2503 PN25.
CHARACTERISTICS:
– The dismantling joint enables easy installation and dismantling of isolating valves, not return valves, low metering equipment, pumps etc.
– Flanges and tubes with Epoxy coating.
– Threaded rod and nuts are not included in the dismantling joint, it is an option.
– Working conditions NBR: From -1 to 16 bar, from -10 to 80 ºC.
Dismantling Joint Fig. 77
– Flange dimensions and holes according to: DIN 2576 PN10, DIN 2502 PN16 and DIN 2503 PN25.
CHARACTERISTICS:
– The dismantling joint enables easy installation and dismantling of isolating valves, not return valves, low metering equipment, pumps etc.
– Flanges and tubes with Epoxy coating.
– Threaded rod and nuts are not included in the dismantling joint, it is an option.
– Working conditions NBR: From -1 to 16 bar, from -10 to 80 ºC.
Wafer Type Knife Gate Valve Fig. 57
Joining between flanges according to UNE-EN 1092-2 PN10 or ANSI B16.5 ASA 150 lbs.
Characteristics:
– Monobloc body.
– Full bore: allows a high flow with low head loss.
OPTIONS:
– With handwheel and
metal seal.
– With handwheel and
EPDM or NBR seal.
– With double acting
Pneumatic actuator
and metal seal.
– With double acting
pneumatic actuator
and EPDM or NBR
seal.
– Others…
Lug Type Knife Gate Valve Fig. 57 LUG
Joining between flanges according to UNE-EN 1092-2 PN10 or ANSI B16.5 ASA 150 lbs.
Characteristics:
– Monobloc body.
– Full bore: allows a high flow with low head loss.
Ductile Valve Fig. 45N
– Flange dimensions and holes according UNE-EN 1092-1 PN10 / PN16.
SPECIALS CONSTRUCTIONS:
On demand the valves could manufactured:
– With extension spindle and handwheel.
– With extension spindle and electric actuator.
– With extension spindle and gear-box.
– Others…
Threaded Ends “Y” Type Strainer Fig 43
Threaded ends according to: DIN 259 / 2999.
OPTIONS:
– Bosy-bonnet gasket in rubber, carton or graphite.
– Available in any screen perforation.
– Plugs before and after the screen for checking drop pressure.
Flanged “Y” Type Strainer (450 – 700) Fig. 42
– Face to face dimensions according to EN 558-1 Serie 1. DIN 3202-1 / F1.
– Flanges dimensions according to UNE-EN 1092-2 PN16 (From Ø15 to Ø400).
– Flanges dimensions accord. to UNE-EN 1092-2 PN10 or PN16 (From Ø.
OPTIONS:
– Body-bonnet gasket in rubber, carton or graphite.
– Available in any screen perforation.
– Plugs before and after the screen for checking drop pressure
Flanged “Y” Type Strainer (15-400) Fig. 42
– Face to face dimensions according to EN 558-1 Serie 1. DIN 3202-1 / F1.
– Flanges dimensions according to UNE-EN 1092-2 PN16 (From Ø15 to Ø400).
– Flanges dimensions accord. to UNE-EN 1092-2 PN10 or PN16 (From Ø450 to Ø700).
– Holes dimensions according to UNE-EN 1092-2 PN10 / PN16.
OPTIONS:
– Body-bonnet gasket in rubber, carton or graphite.
– Available in any screen perforation.
– Plugs before and after the screen for checking drop pressure.
